feat: 更新版本至V1.1.54并优化南向写寄存器日志

1 更新协议板版本寄存器值为0x0146
2 调整短路测试启动间隔为100ms
3 修改电压源选择默认值为6
4 移除南向写寄存器调试打印宏
5 新增基于实际通道号的南向写寄存器调试日志
6 同步版本号与日志文档内容

apps/chrg/applications/thread/chrg_comm.c

@@ -27,7 +27,7 @@
 #include "stm32f4xx_hal.h"
 
 #define HOLD_REG_FIRMWARE_VERSION 0x0300U /* 协议板固件版本，只读 */
-#define CHRG_FIRMWARE_VERSION     0x0145U /* 当前协议板版本：V1.1.53 */
+#define CHRG_FIRMWARE_VERSION     0x0146U /* 当前协议板版本：V1.1.54 */
 
 
 rt_uint8_t ucDiscInBuf[(TOTAL_DISC_REGS+BITS_UCHAR-1)/BITS_UCHAR];

apps/chrg/applications/thread/chrg_north.h

@@ -16,7 +16,7 @@
 #include "chrg_def.h"
 
 /* V_On启停判定电压源：切换后需重新编译固件。 */
-#define SINK_VON_VOLTAGE_FROM_PROTOCOL  1U
+#define SINK_VON_VOLTAGE_FROM_PROTOCOL  6U
 #define SINK_VON_VOLTAGE_FROM_POWER     2U
 #ifndef SINK_VON_VOLTAGE_SOURCE
 #define SINK_VON_VOLTAGE_SOURCE         SINK_VON_VOLTAGE_FROM_POWER

apps/chrg/applications/thread/chrg_roll_sou.c

@@ -963,6 +963,11 @@ void chrg_roll_sou_thread_entry (void *data)
 				continue;
 			}
 			pROLL->idx = (eIDX_SOU_CH)single_ch;
+			#if SOUTH_COMMAND_DEBUG
+			/* 此处已完成物理通道选通，打印通道号比固定的Modbus从机地址更便于排查。 */
+			rt_kprintf("south write: ch=%d reg=0x%04x value=0x%04x\n",
+				single_ch + 1U, single_reg, single_value);
+			#endif
 			chrg_eload_write_reg(ID_ELOAD, single_reg, single_value);
 		}
 		break;
@@ -983,6 +988,11 @@ void chrg_roll_sou_thread_entry (void *data)
 				continue;
 			}
 			pROLL->idx = (eIDX_SOU_CH)command_ch;
+			#if SOUTH_COMMAND_DEBUG
+			/* COM批次按选通后的实际通道打印南向写寄存器指令。 */
+			rt_kprintf("south write: ch=%d reg=0x%04x value=0x%04x\n",
+				command_ch + 1U, command_reg, command_value);
+			#endif
 			chrg_eload_write_reg(ID_ELOAD, command_reg, command_value);
 		}
 		break;

apps/chrg/applications/utils/chrg_def.h

@@ -14,8 +14,8 @@
 /* CHRG application version. Keep this value synchronized with the changelog. */
 #define CHRG_VERSION_MAJOR       1U
 #define CHRG_VERSION_MINOR       1U
-#define CHRG_VERSION_PATCH       53U
-#define CHRG_VERSION_STRING      "V1.1.53"
+#define CHRG_VERSION_PATCH       54U
+#define CHRG_VERSION_STRING      "V1.1.54"
 
 /*
  * Channel polling mode:

apps/chrg/applications/utils/chrg_eload.c

@@ -276,10 +276,6 @@ int chrg_eload_read_regs (rt_uint8_t addr, rt_uint16_t reg, rt_uint16_t len)
  	u16_to_u8v(value, &buf[4]);
  	crc = mb_crc16(buf, 6);
  	u16_to_u8v(swap_u16(crc), &buf[6]);
-#if SOUTH_COMMAND_DEBUG
-	rt_kprintf("south write: addr=%d reg=0x%04x value=0x%04x\n",
-		addr, reg, value);
-#endif
 	return chrg_south_send(buf, 8);
 }
 

apps/chrg/applications/utils/chrg_sink.h

@@ -21,7 +21,7 @@ struct chrg_switch_t;
 #define SINK_TEST_OCP   2
 #define SINK_TEST_DYNA  3
 /* 短路测试期间按该周期补发WORK_START，防止功率板因超时停止。 */
-#define SINK_SHORT_START_INTERVAL_MS  50U
+#define SINK_SHORT_START_INTERVAL_MS  100U
 /* 短路测试不受普通V_ON门槛限制，功率板使用最低启动电压。 */
 #define SINK_SHORT_TEST_VON_MV        500U
 //短路测试结构体